Miren acabo de adquirir mi PS3 y pues estoy como niño con juguete nuevo pero los juegos son carisimos y obio me quedo con ganas de jugar mis juegos de PS2 copias, en la PS3 es estado buscando y no esta tan lejos el chip de PS3 esto es en si el chip actual para la PS3 sin tanta bronca.


NOTA: DOY 15000.00 PTS.

A QUIEN ME LO TRADUSCA A LA PERFECCION EN ESPAÑOL Y ME LO MANDE EN UN ARCHIVO WORD 2003 A MI CORREO cochicueva@hotmail.com. con todo e imagenes. (no usen algun traductor pues no queda entendible ya lo intente yo quiero una traduccion PROFESIONAL.)

Aqui se los dejo y diganme apoco no promete mucho.

Esto en si crea un puenteo para sacar y meter con libertad los discos sin que el sistema se de cuenta que el disco salio es muy similar al swap magic, con switch conectado directamente al laser expulsa el dvd original de PS2 una vez la maquina lo haya reconocido sin que el sistema se percate de su salida, luego con el mismo switch introduces la copia y el sistema ni enterado que algo paso luego lo ejecutas desde el XBM (menu) y lo carga como si nada. ASI DE SENCILLO.




OK, I wanted a fairly easy way to play my PS2 backups on my
PS3. I have read that you can do it by taking apart your PS3
and cutting a hole in the top and yadayada. Leaving the top
off of my PS3 to play PS2 backups didn't sound attractive to
me. So i searched around and found a forum for PS2 talking
about a tray switch for the fat PS2's back in the day. So i
did some brainstorming and figured it might work. I went to
Radio shack and purchased a 3 way toggle switch for $5. I
highly recommend 3 way. At radio shack it was called a middle
off switch. That way your drive motor is not constantly running.
I came home and soldered the wires to the switch.

A note before we start. This is a fairly easy process, the
most trouble i had was trying to figure out where to put the
switch. there is no room to work with. I ended up taking out
my card reader on my PS3 because i never use it and just mounted
the switch there. You could possibly let it hang out. It's up to
you. Just remember that if you plan to retain original
functionality as far as the drive sensor and automatic load/unload motor, you will need 2 additional small on/off switches.


The Switch I purchased:






1- Solder a wire from pin 6 to pin 1.



2- Solder a wire from pin 3 to pin 4.



3- Solder a RED wire to pin 4, and a BLACK wire to pin 1. This
will be your power wires that run to your Blu-ray load/unload
motor. I'd say make the length about a foot just to be safe. You
can cut off what you don't need later.




4- Pin 2 and pin 5 are the power source. Doesn't matter which
way you connect those. I'm using a plug-in power adapter with
an output switch on it up to 12 volts. It's set at 3 volts





That's the hard part if you can believe it. Now you gotta bust
open the PS3. Very easy to do and no cutting or breaking involved.

1- Take the one bolt out on the side and slide the top off.

2- take the rest of the screws out and take the second top off.
This will expose the Blu-ray drive.



3- the Blu-ray drive has 2 plug-ins that need to be unplugged.
after that it comes out freely.

A- A ribbon on the bottom




B- A small plug-in on the left side




Note: Your main goal is to get to some small screws on the
bottom so that you can remove the metal cover. You may choose
not to unplug anything. That's up to you.

4- Take the metal top off. you will see a small circuit board
with 2 wires towards the front of the drive. This is a sensor
that allows the game to be sucked in. You need to disable this
by either cutting the small wires, Hooking up another small
switch so you still retain original functionality, or put a
small piece of tape over the sensor.



5- Unscrew the plastic top and take that off. This will allow
you to see much more of the drive on the inside.



6- The plastic piece I'm pointing to in the picture above needs
to come off. That will allow us to see the load/unload motor.
One small screw will allow you to remove this plastic part.



7- Once removed you will see the small motor which is what we're
after and makes this possible. You'll see 2 small wires soldered
onto the motor. RED and BLACK. You have another tough choice now,
if you chose to add a switch to the load sensor above, you will
need to add a switch to one of the original motor wires also.
This way, when you put your game in and the sensor sucks it in,
the motor will work automatically like it did to start with. If
you have the sensor turned on with a switch, you need the motor
turned on auto with a switch. that's where the 2 additional
switches come in if you choose to retain original functionality.
If you plan to load and unload games manually you only need
1 3-way switch and can disregard anything I've said about x-tra switches. The foot long wire you solder earlier to pins 4 and 1
now need to be soldered to the RED and BLACK terminals of your
motor. I just touched my soldering iron to the terminals and
removed the factory wires, tucked them away and soldered the
ones from my switch to it.





8- Now what i did was remove 3 small screws from a small circuit
board and ran my wires underneath it. Under the circuit board
there is a small hole that allows you to run the wire underneath
and out the bottom front of the Blu-ray drive. The board I'm
pointing to is the one that needs to be unscrewed. It doesn't
come off all the way but does enough for you to run wire under
it. When you put the screws back in make sure not to tighten
them down too much. just make them snug and make sure the small
switch on the right side of the board is in the proper place.




9- And that's pretty much it. Where you plan to mount the switch
or switches is up to you. the way i have mine set up is when the
switch is up the motor is sucking in. I start to put a game in
and it sucks it in. When the game is in and the drive engaged
i turn the switch to the middle position or off. turn on the
PS3 and the original game or Swap Magic will register with the
xmb. No need to actually boot the original game or swap magic
because as long as the game is recognized by the system, it has
passed any media checks. Next, I flip my switch down and the drive disengages and spits my game out. I then flip the switch back up
and insert my backup and turn the switch off. The whole time you
do the swap, the PS3 will still say you have a game inserted. So
if you choose to try this, you don't need anything special. 1-3 switches and an original PS2 game This is my first tutorial and
I'm sorry if it's bad. Feel free to redo it and repost it.
All i ask is that you don't try and take credit for what i've done. Other than that enjoy, be careful, and have fun.

PS: for my next trick i will get a PS3 backup that fits on a DVD
and insert my original Blu-ray PS3 game and then see if i can swap
it with a PS3 game on a DVD!!!
I have a 60gb U.S. PS3 running Firmware 1.51.

__________________

No es por hechar la sal, pero según lei eso es FAKE asi que pues seria cuestion de que tu lo hicieras.

Saludos y disculpa por no ayudarte en la trducida.

__________________

ojala y fuera cierto eso compañero!
salu2

__________________

De echo es cierto ya me anime y lo probe no esta tan dificil lo malo es que con esto no se asegura que sirva en PS3 solo es para las copias de PS2 pues la ps3 reconoce que disco tiene adentro con nombre y animacion entonces todavia no se sabe si jalaria o no en copias de PS3. mientras estoy feliz aunque de todos modos tengo el PS2 pero ya es un gran avance.

__________________

Esto de cargar backups de PS2 en el PS3 es viejo.
en EOL esta el tuto en español solo es que lo busquen.

y yo que pense que era otra cosa.
bueno,, peor es nada.

Traducir eso es español,, no es un ingles muy tecnico que digamos asi que con cualquier traductor lo sacas, o postea q parte en ingles no entiendes . aunque estoy mas que seguro que en EOL esta en español

__________________

y que hay del antiguo usb xtreme del ps2? no jala en ps3? saludos

__________________

Ese tutorial es para cargar tus backup's de ps2 i psx en la ps3. Haciendolo en la de 60gb hay que quitarle el lector de tarjetas para poder instalar las palancas. Para mi parecer, es destrozar una ps3.

Salu2

__________________

yo tambien habia leido eso de que era fake.

__________________

Si te compraste el PS3 estas conciente que es una distraccion para gente solvente, si no tienes dinero regresa al ps2 ese ya esta comprobado su chip, que bonito es trabajar para comprarse sus juegos originales sin estar preocupados por si sale o no un chip.

Tienes toda la razon es muy como estar sin preocupacion de si el chip nuevo hace mas cosas o si no sirve, claro esta que los juegos son caros pero pues vale la pena no estar preocupado por que se vaya a joder tu ps3
Saludos
Atte: Cordova